Description

1. Download and run Veritas Quick Assist (VQA)
    
2. Accept the EULA
    
3. Click option 4, Network Diagnostics

   

4. Read the network diagnostics introduction, then click Next

   

5. Select one or more network interfaces to use when running the diagnostics

   

6. Add one or more target hosts. Diagnostics will be run between the system running VQA and each of the target hosts.
   1. Click Add Target Host
   2. Enter the target’s hostname or IP address
   3. Click Save
   4. Optionally, repeat steps 6a-c for additional target hosts

   

7. One done adding target hosts, click Next

   

8. If requested by your Veritas Engineer, enter values for Number of Packets to Send and Packet Size.

   * If needed, specify the Number of Runs and the Run Delay.

   * If needed, specify a Start Date and Start Time to schedule the diagnostics to run at a later time.

   Note: Leave the Number of Packets to Send and Packet Size fields blank to use their default values. Leave the Number of Runs and Run Delay fields empty to run the diagnostics once. Leave the Start Date and Start Time fields empty to start the diagnostics immediately.

   Click Next

   

9. Depending on options selected in the previous step, the diagnostics will either begin immediately or they will be scheduled to run at a later date/time. Either way, please leave the screen open until the diagnostics have completed.

   

10. Once the diagnostics have completed, select an option for providing the results to your Veritas Engineer, then click Next

    

11. If you selected Create a new support case or Upload results to an existing support case, when prompted, enter your Veritas account credentials, then click Log In. Follow the directions on the screen to provide the diagnostic data to Veritas.

    If you selected Save results to disk and manually provide to Veritas Support, VQA will notify you of where the data is saved in .vdbz format. Please navigate to the Veritas Support website, click My cases and attach this data package to your Veritas Support case.

    Note: Diagnostic results will be communicated by a Veritas Engineer after the data package has been received and analyzed. 

Linux Instructions

Guided Experience

1. Download and extract the Linux Network Tool.
    
2. Run ./vqacollector vnit
    
3. Choose one or more network interfaces to use when running the diagnostics. You may enter the interface number or its name. Multiple interfaces can be selected by listing them separated with a comma (ex. 1,3,5).

   

4. Enter one or more target hostnames or IP addresses. Diagnostics will be run between the system running the Linux Network Tool and each of the target hosts. Multiple target hosts can be specified by listing them separated with a comma (ex. 10.10.10.2,10.10.10.5,10.10.10.9)

   
    

5. If requested by your Veritas Engineer, enter values for Number of packets to send during execution and Size of packet/buffer to send in bytes. If not specified by your Veritas Engineer, press enter for these two questions to accept the default values.

   
    

   Note: Size of packet/buffer to send in bytes will accept values between 1 and 65507

6. Press Enter to accept the default Data Collection Output Directory. Diagnostic results will be stored in a folder called DataCollectionResults in the same folder as the vnit application.

   
    

7. Unless otherwise specified by your Veritas Engineer, press Enter to accept the default value to Process time out in minutes.

   
    

8. If you would like to schedule the diagnostics to run at a later date and time, enter the date and time in the format mm:dd:yyyy hh:mm:ss

   OR

   If you would like to start the diagnostics immediately, press Enter to accept the default value

   
    

9. If needed, specify a value for Execute process x number of cycles/iterations or press Enter to accept the default value of 1. This setting is used to run the diagnostics more than once over a period of time.

   
    

10. If running the diagnostics multiple times as specified in the previous step, specify the delay between the runs in the format hh:mm:ss. Otherwise, press Enter to accept the default value.

    
     

11. Wait for the diagnostics to complete.

    
     

12. Change directories to DataCollectionResults. Provide the .vnit file in this folder to your Veritas Engineer by navigating to the Veritas Support website. Then click My cases and attach this data package to your Veritas Support case.

    
    Note: Diagnostic results will be communicated by a Veritas Engineer after the data package has been received and analyzed.

Command Line Experience

Use the following command line options to run the Linux Network Tool

Syntax: ./vnit -i -t

Example: ./vnit -i ens32 -t 192.168.10.102

Once the diagnostics are complete, please find the .vnit file, located in the DataCollectionResults directory and provide it to your Veritas Engineer by navigating to the Veritas Support website. Then click My cases and attach this data package to your Veritas Support case.

For NetBackup Appliances both Flex and non-Flex, please contact Veritas Technical Support for guidance.